학술논문
Finite Element Analysis of Wrist Orthosis with 3D Printing
이용수 46
- 영문명
- 발행기관
- 한국방사선학회
- 저자명
- 최현우(Hyeun-Woo Choi) 강인영(Inyeong Kang) 노건우(Gunwoo Noh) 서안나(Anna Seo) 이종민(Jong-Min Lee)
- 간행물 정보
- 『한국방사선학회 논문지』 제13권 제7호, 946~953쪽, 전체 8쪽
- 주제분류
- 공학 > 기타공학
- 파일형태
- 발행일자
- 2019.12.30
4,000원
구매일시로부터 72시간 이내에 다운로드 가능합니다.
이 학술논문 정보는 (주)교보문고와 각 발행기관 사이에 저작물 이용 계약이 체결된 것으로, 교보문고를 통해 제공되고 있습니다.
국문 초록
임상에서 사용하는 진단 검사 장치인 전산화 단층촬영기와 자동화된 설계 소프트웨어(MediACE 3D Program), 3D 프린터로 손목 보조기를 제작하고자 하였다. 전산화단층촬영기로 상지의 Dicom 파일을 획득한 후 MediACE 3D Program을 통해 손목 보조기를 디자인하여 STL(stereolithography) 파일을 만들었고, 디자인된 손목 보조기는 3D 프린터를 이용하여 인쇄하였다. 3D 프린팅 기술로 제작된 손목보조기의 효용성 검증을 위해 뼈와 피부에 가해지는 압력 및 보조기의 스트레스 분포를 유한요소해석으로 나타내었다. 손목 보조기를 제작할 때 유한요소해석의 결과를 가지고 뼈와 피부가 압력에 의한 손상과 보조기의 파손이 자주 일어나는 부위를 보강하여 손목 보조기를 제작할 수 있을 것이라고 기대된다.
영문 초록
The purpose of this study was to manufacture a wrist brace using a computerized tomography system, clinical design software (MediACE 3D Program), and 3D printer. After acquiring the Dicom file of the upper limb with a computed tomography, the wrist brace was designed using the MediACE 3D Program to create a stereolithography file. The designed wrist brace was printed using a 3D printer. To verify the effectiveness of wrist assistive device manufactured by 3D printing technology, the stress distribution of the pressure and orthosis applied to bone and skin is represented by finite element analysis. It is expected that the wrist brace can be manufactured by reinforcing the part where the damage caused by pressure and breakage of the brace frequently occurs with the result of finite element analysis when producing the wrist brace.
목차
ABSTRACT
Ⅰ. INTRODUCTION
Ⅱ. MATERIAL AND METHODS
Ⅲ. RESULT
Ⅳ. DISCUSSION
Ⅴ. CONCLUSION
Reference
키워드
해당간행물 수록 논문
- The Effect of Radiological Technologist Organizational Culture, Leadership and Organizational Commitment on Organizational Satisfaction
- Evaluation of Dose Distribution of 6 MV X-ray using Optical Dosimetry
- Investigation of Leksell GammaPlan’s ability for target localizations in Gamma Knife Subthalamotomy
- A Comparison of Density and Patient Doses According to kVp and mAs Changes in General Radiography
- Assessment of Image Quality of Dual Energy 256 MDCT Technique Focused on keV Changes for MCA Stroke in Cerebral Angiography : Single Energy CT Standard Reference Mode
- Finite Element Analysis of Wrist Orthosis with 3D Printing
- A Study on the Analysis of Risk Factors and Correlations of Coronary Artery Disease of the Examinee taking Coronary Computed Tomography Angiography in a Comprehensive Health Improvement Center
- A Study on the Artifact Reduction Method of Magnetic Resonance Imaging in Dental Implants and Prostheses
- Application of Dual Tree Complex Wavelet for Performance Improvement of CT Images
- Usefulness of Silicon Bolus Using 3D Printing of Head and Neck Patients
- Calculation of Neutron Energy Distribution from the Components of Proton Therapy Accelerator Using MCNPX
- Measurement of Radiation Dose of HR CT and Low Dose CT by using Anthropomorphic Chest Phantom and Glass Dosimetry
- Usefulness Evaluation and Fabrication of the Radiation Shield Using 3D Printing Technology
- Preliminary Research on the Implementation of Information of Human Facial Part Required for the 3D Printing of Eye Shield
- A Study of the Quantitative, Qualitative Analysis on Optimizing Diagnostic Imaging Device Selection in Nasopharynx MRI
- A Study Radiograph Techniques for Diagnosis of Axillary Fracture Ribs in X-ray
- Usefulness of Dual Energy CT to Improve Image Quality Degradation due to Lens Shielding
참고문헌
관련논문
공학 > 기타공학분야 BEST
더보기공학 > 기타공학분야 NEW
- 고분해능 및 고민감도를 위한 준 블록 섬광체를 사용한 네 층의 반응 깊이 측정 검출기 설계
- 기분장애 환자의 대뇌 피질 두께 측정에 관한 연구
- 양방향 흐름 팬텀 모델에서 탄산수의 도플러 유체 효과 연구
최근 이용한 논문
교보eBook 첫 방문을 환영 합니다!
신규가입 혜택 지급이 완료 되었습니다.
바로 사용 가능한 교보e캐시 1,000원 (유효기간 7일)
지금 바로 교보eBook의 다양한 콘텐츠를 이용해 보세요!