학술논문
A Study on the Fabrication of bone Model X-ray Phantom Using CT Data and 3D Printing Technology
이용수 48
- 영문명
- 발행기관
- 한국방사선학회
- 저자명
- 윤명성(Myeong-Seong) 한동균(Dong-Kyoon Han) 김연민(Yeon-Min Kim) 윤준(Joon Yoon)
- 간행물 정보
- 『한국방사선학회 논문지』 제12권 제7호, 879~886쪽, 전체 8쪽
- 주제분류
- 공학 > 기타공학
- 파일형태
- 발행일자
- 2018.12.30
4,000원
구매일시로부터 72시간 이내에 다운로드 가능합니다.
이 학술논문 정보는 (주)교보문고와 각 발행기관 사이에 저작물 이용 계약이 체결된 것으로, 교보문고를 통해 제공되고 있습니다.
국문 초록
3-dimensional(D) 프린터는 컴퓨터로 모델링 한 데이터를 바탕으로 3차원의 입체 물체를 출력할 수 있는 장비이다. 이러한 특징을 방사선과학 분야와 융합하여, CT 데이터를 이용한 뼈 모형 X선 팬텀제작 등에 활용되고 있다. 본 연구는 기존의 Pelvis팬텀을 CT 스캔하고 얻어진 데이터로 Fused Filament Fabrication(FFF) 3D 프린터의 소재인 PLA, Wood, XT-CF20, Glow fill, Steel 필라멘트를 이용하여, 뼈 모형 팬텀을 제작하였다. 기존의 Pelvis 팬텀과 3D 프린터로 제작된 5가지 재질의 팬텀을 동일한 조건으로 CT 스캔 하고 얻어진 영상에서 Hounsfield Unit(HU)을 측정하였으며, 진단용X선 발생장치를 이용하여 SI, SNR을 측정하여 각 팬텀을 비교 분석하였다. 그 결과 사지 X선 검사 조건 내에서 X선 팬텀은 glow fill 필라멘트가 가장 적합하다는 것을 알 수 있었다. 본 연구의 기반으로 필라멘트의 특성들을 알 수 있었으며, X선 팬텀 제작에 대한 실용
성을 확인하였다.
영문 초록
A 3-dimensional (D) printer is a device capable of outputting a three-dimensional solid object based on data
modeled in a computer. These features are utilized in the bone model X - ray phantom production etc using CT
data by fusing with the radiation science field. A bone model phantom was made using data obtained by CT scan
of an existing Pelvis phantom, using PLA, Wood, XT-CF20, Glow fill, Steel filaments which are materials of
Fused Filament Fabrication (FFF) 3D printer.Measure Hounsfield Unit (HU) with images obtained by CT scan of
the existing Pelvis phantom and five material phantoms made with 3D printer under the same conditions,SI and
SNR were measured using a diagnostic X-ray generator, and each phantom was compared and analyzed.As a
result, the X - ray phantom in the X - ray examination condition of the limb was found to be most suitable for
the glow fill filament.The characteristics of the filament can be known to the base of this research and the
practicality of X - ray phantom fabrication was confirmed.
목차
Ⅰ. INTRODUCTION
Ⅱ. MATERIAL AND METHODS
Ⅲ. RESULT
Ⅳ. DISCUSSION
Ⅴ. CONCLUSION
해당간행물 수록 논문
- A Comparison Analysis of CT Effective Dose and Image Quality according to Abdominal Diameter
- Assessment of Effective Dose for General Radiography of Adults Based on Diagnostic Reference Level(DRL) by Using PCXMC Program
- A Study on Safety Management Inspection of Diagnostic X-ray System
- Journal of the Korean Society of Radiology
- Assessment of Radiation Shielding Ability of Printing Materials Using 3D Printing Technology
- Monte-carlo Simulation for X-ray Photon Counting using MPPC Arrays
- Analysis of Health Insurance Standards and Utilization of MRI in Korea:
- Analysis of the Relationships according to the Frame (f/s) Change of Cine Imaging in Coronary Angiographic System: With Focus on FOV Enlargement and Live Zoom
- The Study on Correlation between Carotid IMT and Colon Polyps
- Shielding Capability Evaluation of Mobile X-ray Generator through the Production assembled Shield
- Cross Calibration of Dual Energy X-ray Absorptiometry Equipment for Diagnosis of Osteoporosis: between Domestic Manufacturers and Global Manufacturers
- MDCT Angiography of the Subclavian Artery Thrombosis of the 3D Findings
- A Study on the Fabrication of bone Model X-ray Phantom Using CT Data and 3D Printing Technology
- Analysis of Satisfaction and Problems of Clinic Radiological Technologist on the Supplementary Education
- Error Analysis of General X-ray Examination by Using Simulation Training
- 한국방사선학회 논문지 12권 7호 목차
- Analysis of the Dead Layer Thickness effect and HPGe Detector by Penelope Simulation
- Calculation of Effective Dose on Domestic Chest PA X-ray Examinations
참고문헌
교보eBook 첫 방문을 환영 합니다!
신규가입 혜택 지급이 완료 되었습니다.
바로 사용 가능한 교보e캐시 1,000원 (유효기간 7일)
지금 바로 교보eBook의 다양한 콘텐츠를 이용해 보세요!