학술논문
Mechanical Properties of Magnesium Alloy Extrusions Processed from Machined Chips
이용수 5
- 영문명
- 발행기관
- 호서대학교 공업기술연구소
- 저자명
- Chang Suk Han Sung Yooun Jin
- 간행물 정보
- 『공업기술연구 논문집』제37권 제1호, 8~14쪽, 전체 7쪽
- 주제분류
- 공학 > 공학일반
- 파일형태
- 발행일자
- 2018.06.30
4,000원
구매일시로부터 72시간 이내에 다운로드 가능합니다.
이 학술논문 정보는 (주)교보문고와 각 발행기관 사이에 저작물 이용 계약이 체결된 것으로, 교보문고를 통해 제공되고 있습니다.
국문 초록
영문 초록
Mechanical properties in the AZ9l magnesium alloy extrusions processed from machined chips were examined by tensile tests at 573 K to investigate superplastic behavior. The grains of the extrusions were almost equiaxed, which shows that grain refinement was achieved by hot extrusion. Grain sizes of the extrusions processed at 573, 673 and 753 K were 7.6, 15.4 and 60.1 μm, respectively. The extrusion processed at 573 K showed a maximum elongation of 230% at 3.3×10⁻⁴s⁻¹, which corresponds to the strain rate range where high m was found. For the extrusions processed at 673 K, a maximum elongation was about 100% at 1.7×10⁻⁴s⁻¹. For the extrusion processed at 753 K, elongations to failure were less than 30% at all strain rates. Cavities were nucleated for the extrusion processed from the machined chips, on the other hand, no cavity was observed for the extrusion processed from the cast ingot. For the extrusions processed from the machined chips, oxides which exist on the surfaces of the machined chips were dispersed by hot extrusion. Therefore it is pointed out that it is required to achieve more homogeneous dispersion of the oxide layers and smaller grain size in order to obtain excellent superplastic potential for the materials processed from machined chips.
목차
ABSTRACT
Ⅰ. INTRODUCTION
Ⅱ. EXPERIMENTAL PROCEDURES
Ⅲ. RESULTS AND DISCUSSION
Ⅳ. CONCLUSION
REFERENCES
키워드
해당간행물 수록 논문
- 모션 캡쳐를 이용한 원격제어 최근 연구
- Mechanical Properties of Magnesium Alloy Extrusions Processed from Machined Chips
- 대면적 3차원 고분자 미세구조 형성에 관한 연구
- A Study on the Hot Deformation Behaviors and Structural changes of Aluminum Alloy
- 시각별 일사량 예측 모델의 추정오차 검토
- 부채널 공격 대응을 위한 마스킹 기법에 관한 성능 분석
- FUSE를 이용한 문자 디바이스 접근 기법
- 고강도 강재와 콘크리트를 사용한 CFT 합성기둥의 크리프 효과
- 협대역 IoT 무선통신용 주파수합성기의 성능 개선 연구
- 탄소나노튜브의 기계적 응용
- 영화관 화재 탈출 체험 VR 게임 개발 연구
- Spring Creek 유역의 홍수수위 산정을 위한 HEC-RAS 매개변수 민감도 분석
- 분리막 공정을 활용한 호소수 정화 연구
- 양극 산화법을 통한 나노튜브 전극의 합성과 태양전지로의 응용
- 강섬유 콘크리트의 강도 특성 평가
참고문헌
관련논문
공학 > 공학일반분야 BEST
- Soft Power Suit for Knee Motion Assistance
- Design of Lower Limbs for a Humanoid Biped Robot
- Part Ⅳ : Smart High-tech House as a Large-scale Care Robot for the Elderly and Disabled People
공학 > 공학일반분야 NEW
- 수중 환경에 따른 광대역 OFDM의 통신 성능 분석
- 가상국토구현을 위한 국내 디지털트윈 정책 방향과 관련 최신 연구 동향과의 비교연구
- 공기 중 부유 폐 토너 입자의 거동 특성 평가
최근 이용한 논문
교보eBook 첫 방문을 환영 합니다!
신규가입 혜택 지급이 완료 되었습니다.
바로 사용 가능한 교보e캐시 1,000원 (유효기간 7일)
지금 바로 교보eBook의 다양한 콘텐츠를 이용해 보세요!