학술논문
Reduction of Artifacts in Magnetic Resonance Imaging with Diamagnetic Substance
이용수 35
- 영문명
- 발행기관
- 한국방사선학회
- 저자명
- 최우전(Woo Jeon Choi) 김동현(Dong Hyun Kim)
- 간행물 정보
- 『한국방사선학회 논문지』 제13권 제4호, 581~588쪽, 전체 8쪽
- 주제분류
- 공학 > 기타공학
- 파일형태
- 발행일자
- 2019.08.30
4,000원
구매일시로부터 72시간 이내에 다운로드 가능합니다.
이 학술논문 정보는 (주)교보문고와 각 발행기관 사이에 저작물 이용 계약이 체결된 것으로, 교보문고를 통해 제공되고 있습니다.
국문 초록
자기공명영상검사는 조직의 대조도 와 해상력이 우수하지만, 인공물이 발생 될 경우 진단에 영향을 주어판독이 불가능한 영상을 생성하기도 한다. 치아에 삽입된 금속은 강자성체 또는 상자성체로 되어있는 경우가 대부분이며 자화율 차이로 인하여 기하학적 왜곡을 유발하여 영상진단에 저해되는 경우가 많으며 이를 저감시킬 필요가 있다. 이에 본 연구는 반자성 물질을 사용에 따른 금속 인공물 분석을 실시하고자 한다. 자성 물질로는 치아교정용 와이어와 브라켓인 스테인리스 스틸이 사용되었고 반자성 물질은 구리, 아연, 비스무트를 사용하였다. 검사장비는 1.5T, 3T가 사용되었으며 사용된 시퀀스는 SE, TSE, GE, EPI을 사용하여 측정하였다. 자체 제작된 팬텀을 물질은 균등한 신호를 위하여 아가로스 겔(10%)을 사용하였으며 인공물 유발 물질은 스테인리스 스틸은 팬텀의 정중앙에 위치시켜 검사하고 각 길이 10mm의 정 육면체 반자성물질의 씌워 검사하였다. 인공물 측정은 Image J를 사용하여 순수한 팬텀 영상에서 자성물질을 포함한 영상을 감산하여 얻은 영상에서 Low Threshold 값을 10으로 설정 한 후 Wand tool을 사용하여 인공물 영역설정 후 면적을 구하였다. 스테인리스 스틸에서 발생한 금속 인공물은 반자성 물질 중 비스무트를 사용한 영상에서 금속 인공물이 가장 많이 감소하였으며 구리와 아연은 약간은 감소하지만, 그 정도의 차이는 크지 않다고 하겠다. 이러한 이유는 비스무트의 반자성 자화율이 가장 작아서 강자성체에서의 자화율을 가장많이 상쇄하였기 때문이라고 생각된다. 1.5T 와 3T 모두에서 비스무트를 사용한 영상의 인공물이 가장 적게 나왔다. 시퀀스별 인공물 감소는 1.5T에서는 TSE에서 가장 많이 인공물이 감소하였으며 3T에서는 SE에서 가장 많은 인공물이 감소하였다. 따라서 반자성물질의 따른 인공물 변화의 결과는 자화율(χ)이 가장 낮은 비스무트를 사용한 영상에서 금속인공물이 기준인 Implant 인공물 보다 줄어든 양상을 보여 자화율이 낮은 물질일수록 금속 인공물이 줄어든다는 것을 알 수 있었으며, 기존 금속 인공물의 해결 방법의 단점으로 지적되어온 스캔 시간의 증가 등이 나타나지 않으면서도 인공물을 줄일 수 있는 방법으로 향후 치아 교정 물질뿐만 아니라 치아 보철물 전체에 대한 금속 인공물 저감에 관한 연구의 기초 자료로 사용될 것으로
사료된다.
영문 초록
MRI is superior when contrasted to help the organization generate artifacts resolution, but also affect the
diagnosis and create a image that can not be read. Metal is inserted into the tooth, it is necessary to often be
inhibited in imaging by causing the geometric distortion due to the majority and if the difference between the
magnetic susceptibility of a ferromagnetic material or paramagnetic reducing them. The purpose of this study is
to conduct a metal artefact in accordance with the analysis using a diamagnetic material. The magnetic material
include a wire for the orthodontic bracket and a stainless steel was used as a diamagnetic material was used
copper, zinc, bismuth. Testing equipment is sequenced using 1.5T, 3T was used was measured using a SE, TSE,
GE, EPI. A self-produced phantom material was used for agarose gel (10%) to a uniform signal artifacts causing
materials are stainless steel were tested by placing in the center of the phantom and cover inspection of the
positive cube diamagnetic material of 10mm each length.After a measurement artefact artifact zone settings area
was calculated using the Wand tool After setting the Low Threshold value of 10 in the image obtained by
subtracting images, including magnetic material from a pure tool phantom images using Image J. Metal artifacts
occur in stainless steel metal artifact reduction was greatest in the image with the bismuth diamagnetic materials
of copper and zinc is slightly reduced, but the difference in degree will not greater. The reason for this is thought
to be due to hayeotgi offset most of the susceptibility in bismuth diamagnetic susceptibility of most small
ferromagnetic. Most came with less artifacts in image of bismuth in both 1.5T and 3T. Sequence-specific artifact
reduction was most reduced artifacts from the TSE 1.5T 3T was reduced in the most artifacts from SE.
Signal-to-noise ratio was the lowest SNR is low, appears in the implant, the 1.5T was the Implant + Bi Cu and
Zn showed similar results to each other. Therefore, the results of artifacts variation of diamagnetic material,
magnetic susceptibility (χ) is the most this shows the reduced aspect lower than the implant artificial metal
artifacts criteria in the video using low bismuth susceptibility to low material the more metal artifacts It was
found that the decrease. Therefore, based on the study on the increase, the metal artifacts reduction for the whole,
as well as dental prosthesis future orthodontic materials in a way that can even reduce the artifact does not
appear which has been pointed out as a disadvantage of the solutions of conventional metal artifact It is
considered to be material.
목차
Ⅰ. INTRODUCTION
Ⅱ. MATERIAL AND METHODS
Ⅲ. RESULT
Ⅳ. DISCUSSION
V. CONCLUSION
키워드
해당간행물 수록 논문
- Reduction of Artifacts in Magnetic Resonance Imaging with Diamagnetic Substance
- 3D Fusion Imaging based on Spectral Computed Tomography Using K-edge Images
- Comparison of Practical Usefulness of Respirational Radiation Treatment Using Geant 4 Simulation Code
- Feasibility Study of Non Local Means Noise Reduction Algorithm with Improved Time Resolution in Light Microscopic Image
- Prediction of Entrance Surface Dose in Chest Digital Radiography
- Utility Evaluation of Supportive Devices for Interventional Lower Extremity Angiography
- Evaluating the Effects of Inferiority Management Using a Group Counseling Program for University Students in Health Science
- Produced Body Customized 3D Print Finger Brace using Dicom File
- The Study on Interpretation of the Scatter Degradation Factor using an additional Filter in a Medical Imaging System
- The Study of Radiation Exposed dose According to I Radiation Isotope Therapy
- A Study on the Change of Image Quality According to the Change of Tube Voltage in Computed Tomography Pediatric Chest Examination
- Study on the Development of an Outdoor Radiographic Test Shield Using 3D Printer Filament Materials
- Evaluation of Stage of Liver Fibrosis by Ultrasonography : Based on Pathologic Results of Biopsy
- Image Compression by Linear and Nonlinear Transformation of Computed Tomography
- Comparison of X-ray Image Quality Between Multi-Function Device(MFD) and Weight Bearing Platforms(WBPs)
- Psychological Systematic Consideration of Breast Cancer Radiotherapy
- The Study for the Relation between Fatty Liver Diagnosed by Abdominal Ultrasonography and Hyperlipidemia
- Determination of Effective Energy of CT X-ray beams
- Analysis of the Entrance Surface Dose (ESD) and Contrast Usage of Trance Femoral Cerebral Angiography (TFCA) and Cerebral Computed Tomographic Angiography (CCTA) for Cerebrovascular Disease Examining
- The Measurement of Spatial Dose Rate by Gravity Ventilation after Technegas Scanning
- Design of Gamma Camera with Diverging Collimator for Spatial Resolution Improvement
- Luminescence Properties of Europium-doped NaSr(PO3)3 Phosphor
- Consideration of Cut-off Value for Fibrosis Serum Marker by Liver Fibrosis Stage in Chronic Hepatitis C Patients
참고문헌
교보eBook 첫 방문을 환영 합니다!
신규가입 혜택 지급이 완료 되었습니다.
바로 사용 가능한 교보e캐시 1,000원 (유효기간 7일)
지금 바로 교보eBook의 다양한 콘텐츠를 이용해 보세요!